The desk is homemade. A couple cabinets, wood countertops from Home Depot and a few other parts.
Yes it’s two .270 Weatherby cartridges.
Thanks, I like it a lot.
I think it was around $20. You can get them on Newegg
No this is how I wanted it. The cooler is run off the motherboard argb header. I didn’t use the cooler Master controller at all.
Thanks! The GPU brace is 2 expended .270 rifle cartridges. All the RGB fans, light strips and motherboard lights are in sync. The pump, cooler fans and one set of lights on the motherboard are set to ARGB.
It came with an acrylic front. I bought the mesh front for it.
Have all 8 cores at 5ghz and haven’t noticed any issues so far.
There wasn't much of a difference. I think the cpu was cooler as intake but the gpu was a little warmer. Not a big difference though.
I like it. I build a lot of computers in different cases and it is one of the best I have ever used. I have the mesh front panel on it and it has good airflow and temps.
Cooler Master H500p with the mesh front and the Corsair Carbide 300r. I like the h500p, it has more room, temp is about the same if you have the mesh front and it has good cable management. I have my main build in that case in my other builds.
Its at 4.8 right now. It runs fine at 5 I just like the temps better at 4.8.
Airflow is very good. I have the mesh front on it now but even with the acrylic front it wasn’t as bad as certain reviews said. I currently have this case and a Meshify C in another build. I like this case better hands down.
I haven't had it together for long but no issues so far. The sound seems to be pretty good but I am no audiophile.
I had this gpu already. I didn’t buy it for $200. I just set that as the price as they sell for around that on eBay in Canadian $$. My main build has a 1080 ti and 9900k. I will be posting it on here pretty soon.
Its not bad lol. Still good for 1080p gaming. Not much worse than a 1060.
They are working well so far.
I didn’t experience anything bad with them
I was really impressed with them for the price
Says the guy who comments on everyone’s posts and tells them the better parts they could have bought because they cost $10 less here or $20 less there. While not knowing what the op paid.
Nice build. Nothing wrong with that cpu for 1080p gaming.
The gpu and cpu, mobo & ram were purchased locally used. This was built for fun. My main stystem is a 8700k, 1080 ti build. Can be seen in my builds. The 580 is quite a bit better than the 1050 ti and neither of those cpu’s Are significantly faster than the 6600k
Looks good. Are those 120 or 140mm fans in the front?
I plugged them into the RGB headers on the motherboard. If you don’t have these headers you will need to get a controller I believe.
I never tried it. I was tempted to but I heard they run hotter that way.
Yes they were pulling air through the cooler then out the top of the case. It worked fine with these fans, Corsair ML fans. I later switched to Cooler Master Masterfan Pro rgb fans and they did not work as well. I switched them to push and they still didn't work as well lol.
I ordered it from Savant Pc's.
Yes they can be replaced. You can put 3 140mm fans in place of the 2 200mm
You have them plugged into the motherboard? I don't have any issues using RGB fusion to control them, you select Digital LED C1 or C2 under the advanced tab.
Sorry for the delay. I Never had any issues. Everything went together easily and works well.
I haven't had any issues with it. The XMP worked fine.
2 of them are on the cooler and one is the rear exhaust fan. I replaced the loud stock cooler fans.
I have the voltage set at 1.36 with all of the power saving options turned off I believe.
Very nice. I have the same case also with a 8700k. I would recommend doing the delid, those temps seem awefully high. I kept the stock 200mm fans and my cpu only hits mid to high 60's stress testing and low 60's gaming but it is at 5ghz, delided with a H115i.
I did some real world testing with my case, with the front open vs off. There was only a 3c difference in cpu temp. The case seems to have decent enough airflow in my build anyways.
+1 Great build!
I was looking for a full tower before I got this but I just couldn't find the right one. My last one was the CM Storm Trooper. It was a great case but is showing its age quite a bit now.
Thanks. I got the desk at staples quite a while ago lol.
Thanks. I like the case. I don't have any issues with it. The top and front do open easily but I am pretty sure that is by design. It shows right on the box not to pick it up by the front or the top. I am using an AIO maybe that helps with the temps? I hope you like it.
I am happy with it, haven't had any issues.
The turbo functions get turned off
It’s a funky lamp with a rgb base
Yeah the big one is to cover all the scratches in my desk lol