Description

Use machine primarily for gaming. Really feel in love with water cooling and the aesthetics of everything. Cables where all custom sleeved by myself and coolant is EK Cryofuel Lime Yellow UV Reactive.

Log in to rate comments or to post a comment.

Comments

  • 26 months ago
  • 4 points

this build deserves to be featured. +1 from me nice build :)

  • 26 months ago
  • 2 points

Ty :)

  • 26 months ago
  • 2 points

Nice work on the cable sleeving. That can be a chore.

  • 26 months ago
  • 1 point

Thanks! Time consuming no doubt. Tried to sleeve every cable. Usb 3.0 motherboard cable hard to get though

  • 26 months ago
  • 2 points

Smexy

  • 26 months ago
  • 1 point

Very nice work. That fluid is immense and very different. Nice +1

  • 26 months ago
  • 1 point

Ty :)

  • 26 months ago
  • 1 point

sllimmy ( ͡° ͜ʖ ͡°)

  • 26 months ago
  • 1 point

Jealous. Love it! +1

  • 26 months ago
  • 1 point

Absolutely beautiful, simple and clean. If this hasn't been featured yet, it should be.

  • 26 months ago
  • 1 point

sex

  • 26 months ago
  • 1 point

I have EK Cryofuel Green UV reactive in my build but haven't gotten it to poo quite like yours. What lighting are you using?

  • 26 months ago
  • 1 point

using the cablemod UV led strip and 4 x 3mm UV Led's in GPU and CPU block.

  • 26 months ago
  • 1 point

Really has a nice "Nuclear reactor" theme to it in my opinion. Great build

+1 from me

  • 26 months ago
  • 1 point

Can you point me in the direction to acquire a similar reservoir/pump? Could I get the brand/model names please? Great looking build.

  • 25 months ago
  • 1 point

It is the ekwb xres ddc pump/res combo

  • 26 months ago
  • 1 point

What backplate did you use to mount the graphics card to ?

  • 25 months ago
  • 2 points

The card came with a stock backplate

  • 25 months ago
  • 1 point

I was asking about the back plate for the case

  • 26 months ago
  • 1 point

Gorgeous build! Can you please comment on the vertical mounting of the GPU. Did you use the additional bracket from Lian Li? is there enough space in the bottom for the radiator or did you mod it?

  • 25 months ago
  • 1 point

I modded my own bracket. The lian li bracket you can buy doesnt allow you to mount a bottom radiator

  • 25 months ago
  • 1 point

I see Thanks a lot

  • 23 months ago
  • 1 point

How did you mod the vertical mount?

  • 16 months ago
  • 1 point

nice build dude, just a question on the verticle gpu holder, where did you get it from? or diy?

  • 16 months ago
  • 1 point

This is definitely the coolest PC-O11 build i have seen in here.

I really love the 3rd last picture. Is there any lighting on inside the case on that picture? Or is it just natural lighting from the room?

  • 16 months ago
  • 1 point

I might actually rip off most of your setup in my next project.

But i would change it a little bit, since i love distro plates.

Check this out

Then i could bring a ram waterblock into the loop.

[comment deleted]
[comment deleted by staff]
  • 26 months ago
  • 1 point

Hmm thats not a bad idea never bent hard tube like that maybe will give it a shot

[comment deleted by staff]
  • 26 months ago
  • 1 point

no way to do it with soft tube it would just be all over the place.

[comment deleted by staff]