I ended up naming my new PC "Baby" due to me joking about it being my little baby PC, and the name stuck...

The full post kind of winds up deep in the TL;DR territory, so feel free to skip to the more interesting sections like component reasoning.

This rig came together after about 3 months of research and design, plus advice from good friends of mine with PC building experience. This site and community, along with Tom's Hardware and community, plus a bit of help from Reddit, were indispensable during the research and design period.

I should note that while my rig uses the i5 4690K, I mention the i5 4670K in my reasoning as this was the CPU I originally planned to use. I ended up using the i5 4690K because just as I bought my CPU/motherboard bundle, they had stopped selling the i5 4670K, so I chose the updated bundle with the i5 4690K.

Preamble: My rig was built for gaming and recording/editing said games, plus any random stuff like minor photo editing and whatnot. I wanted this rig to be quiet and reliable, thus the case (quiet) and PSU (reliable), for example. My desire for this rig to be as "future-resistant" (since you can never truly future-proof a PC) as possible while still economically reasonable was one of the biggest driving force of component selection, and one of the largest challenges to the build.

Also of note: this PC was build during the summer of 2014 (June-July), before the huge price cuts after the GTX 970/980 releases

And so, here we go...

Component selection and reasoning:

CPU: I wanted a powerful but reasonably priced CPU, and appreciated the possibility of upgrading to a more powerful CPU, but as a secondary consideration (not the deciding factor). I narrowed my choices down to two CPUs: the AMD FX 8350 (8 cores/8 threads, base clock speed 4GHZ) and the Intel Core i5 4670K (4 cores/4 threads, base clock speed 3.4GHZ) Needless to say, I ran straight into the AMD vs Intel debate, but I eventually decided on Intel for three reasons:

1) From my research, I found the i5 4670K had better single-thread performance than the FX 8350, and was widely considered to be an equal or better gaming CPU

2) The i5 4670K uses the 1150 socket, shared by the more powerful i7 4770K (4 core/8 threads, base clock speed 3.5GHZ), which my research found to be significantly more powerful the FX 8350

3) There was a small enough price difference between my preferred FX 8350/motherboard bundle and my preferred i5 4670K/motherboard bundle that I could justify the extra cost

  • You may be wondering why I didn't see any upgrade potential for the FX 8350. While the FX 8350's AM3+ socket is shared by the more powerful FX 9370 and FX 9590, the power draw and heat output on these chips probably would have been too much for the motherboard I was planning on using, a beefier motherboard would have significantly raised the price, and the increased heat output would have required more expensive cooling.

CPU Cooler: Widely used, highly rated, effective and cheap. Keeps cool under a fairly heavy overclock. 'Nuff said.

Motherboard: Feature rich, reliable and from a reputable company. The layout, styling and general design are good, and I like the design of the BIOS. It has plenty of hardware monitoring and adjustments, which told me that my CL9 RAM is running at CL11 (which I fixed). It's not a big issue, and it's nice that it was so easy to see that in the BIOS. The overclocking interface also seems great so far. I'll see if that continues once I start overclocking more. I also really enjoy the MSI Live Update app for it. Only issue I had with it was installing the extra case fans: I connected them to the onboard fan headers, and some of them worked when I booted it up. Two didn't, and the next time I booted it up, none of them did. I don't know if it was because of the motherboard or the fans (cheap and finicky), but I ended up wiring them to molex instead. Not worth deducting a star for, as I can't tell what caused the issue, and it's fixed anyway.

Memory: Reliable and looks great, although it was running at CL11 instead of CL9, but I fixed that by enabling XMP in the BIOS. 8GB is enough for now (I haven't used all of it yet), and I can always get more (and maybe run a RAM disc). I did notice a sudden drop in the POV-Ray benchmark I was using to stress test and benchmark while overclocking the RAM, but I can't necessarily attribute it to the RAM, as POV-Ray isn't really all that consistent, and it's possible that it's simply the program. I haven't really tried overclocking the RAM since. I may just get a kit of 8-16GB 2133MHz RAM so I never have to bother with overclocking again...

Storage: So far it's been just fine, and should stay that way. Western Digital HDDs are generally considered to be pretty reliable. I may add an SSD later for Windows, games, and a few select programs.

Video Card: This was the other really difficult decision. I wanted something more powerful than a GTX 760/R9 280/R9 270X, but not absurdly expensive. While I don't play extremely graphically intensive games like Crysis 3, or in super high resolution, I still wanted to run stuff as fast as I could and have room to expand to more power-hungry games. I was originally planning on getting the R9 290, but a friend pointed out that I didn't need something that powerful for the games I play (mostly indie games off Steam, but some mainstream and graphics-intensive games too). With that advice, I saved $100 and went with the R9 280X. I chose MSI becuase my research showed their cards tend to be reliable, quiet, and fast, which I can now confirm. I also quite like MSI Afterburner and their MSI Gaming app for adjusting clock speeds. So far, this card has amazed me. It runs War Thunder entirely maxed out, dropping to 88 FPS at the lowest, while still running fairly cool. I was thrilled, as this is something I've never been able to do before (I came off a 2.6GHZ i7 with integrated Intel HD Graphics 4000). Needless to say, it runs Minecraft and Source games very fast, but I haven't had a chance to play many other games.

Case: Highly rated, built well, roomy, sleek and quiet. Only complaint is that one of the HDD trays was bent, but I didn't need it, so it's not really an issue.

Wired Network Adapter: I got sick and tired of the wireless adapter dropping the connection, so I got this and hardwired it. I do occasionally get a "Limited" note with the connection and lose internet access, but I can't tell if it's because of this, the OS, or something else entirely. Anyway, it sure is better than losing my connection so often.

Case Fans:

Kingwin Cheap-Os: Definitely audible (read: loud and annoying) at full speed, which I'm stuck with until I get a separate fan controller. I had to wire 3 of them to molex due to previously mentioned issues (one is wired to the built-in fan controller). These fans seem to have issues with the molex pins coming loose on tight connections, as this happened on two of them. One fan also seemed to have issues starting up while mounted on top of the case. I occasionally had to tap the case to start the fan, but that may have been due to the weird airflow patterns I had set up. (NOTE 02/02/15): I now have the same fan that wouldn't start on my CPU cooler, and it starts fine there. The previous problems with start-up may have indeed been due to the airflow or voltage [I have no idea if either could be the cause, actually]. I am also getting really* tired of the fan noise. I've experimented with closing the door, which helps with the noise but raises the temps by few degrees, which I'm not happy about.

Phanteks: They move over twice as much air as the Kingwins at the same volume, or the about the same amount at a much quieter level. Big improvement over the Kingwins. They also sound better than the Kingwins at full speed. More of a deeper noise...

Headphones/Earphones: Got these separately, but I use them with the PC now, so I figured I'd add them. They're my first pair of "audiophile" headphones, and they sound AMAZING. I also have them hooked up to a Fiio E11k Kilimanjaro 2 portable amp, and it makes them sound even better...

I later bought a pair of Brainwavz Delta IEMs for commuting, and use them with the rig and amp. They not only sound about as good the HD 202s, they also block out the noise of my case fans, which are now starting to bug me.

Build/ PC Issues: Sometimes the headphones aren't recognized when plugged in, so I have to plug them in again. Not sure why, but it's not really a problem... I fixed this by plugging an extender cable to the motherboard output and wrapping it around my monitor stand. It fixes the problem, and it's also easier to plug things in.

Future Upgrades:

None planned. By the time this rig gets obsolete, I'm getting the feeling I'll have moved on to a different rig, and this one will go to a friend.

Sorry for the lack of build-in-progress photos. I took some, but I can't seem to find any now. Unless I find them, I'll have to wait and take pictures if I do a big upgrade (like replacing the CPU cooler or graphics card).

The cable management may look messy, but the side fits on fine (everything lies flat), and nothing obstructs airflow, so it's fine in my book. I have some stuff tied down, but the rest of it holds in place just fine by itself, so there's no reason to waste zip ties tying down stuff that stays flat anyway.

CPU Temps recorded by CPUID HWMonitor CPU stress test done with OCCT and POV-ray GPU temps taken in-game with MSI Afterburner

Clock speeds are overclock speeds only used sometimes. GPU load temp taken in-game, in-game CPU temps to come soon.

PC Blog: This is where my upgrade logs go in real time, along with the latest news. If you want to know what's going on with the rig, this is the place to go. Or if you just want computer nerdery. Because that's what the blog is all about.

UPDATE 01/19/15

I flipped the bottom fan by the PSU to again face upward, feeding fresh air into the GPU. When I originally installed the fan, it was oriented this way, but I later changed it, incorrectly believing the GPU fans were exhaust fans due to a quick test. I tested again with tissue paper, and found the GPU fans were indeed intakes, so I fixed the orientation of the bottom fan.

I then pulled one top fan (the one closest to the front) off the case and stuck it on the CPU cooler for a push/pull configuration. I know it's not really supposed to make all that much difference with the CM Hyper 212 Evo, but I had to pull the fan off anyway, so I stuck it on the CPU. I checked in the BIOS and the motherboard does not recognize that anything is plugged in, but I believe that is because the fans is a 3-pin, not PWM. So far, it runs fine, albeit at full speed, presumably (although that is probably good for my temps, while it is louder). I wanted to remove the fan because it was set as an intake, blowing air down on the CPU cooler and fan. Although this wasn't necessarily creating a problem, I knew this was a bit unusual so I wanted to see if I could get better temps using the space as a vent instead (since I had reservations about using it as an exhaust and possibly stealing available air for the CPU cooler).

CPU load temps seem to be down a few degrees (at least 5⁰C :D). I'll update the CPU and GPU temps once I get more concrete data.

UPDATE 02/15/15

I installed the 850 Evo SSD, which was not fun, and extremely time consuming. Backing up the data took a few hours, since the external drive couldn't copy some files on or off of itself, and it seems to have lost all my AppData, with my Minecraft saves. Installing the SSD took another hour or two, even after I got the extra SATA cable I needed, since I had to unplug all the SATA cables (not fun with the GPU in the way) and change one of them, since the right-angle cable wouldn't work with the position of the SSD. I then had to find an extra power cable and wedge the connected into place behind the bottom fan (I almost wish I had a non-modular power supply, so everything would be in one big bundle, instead of having to plug in cables along the entire back edge of the PSU). After that, I needed to install the OS on the SSD (fairly straightforward), wipe the HDD, and restore my data to it. Maybe I could have used the integrated backup feature in Windows 8.1, but I couldn't find any information about using it for my purposes, so I went with the tried-and-true "backup everything manually." Not fun. As stated before, I lost some of my data, but I backed up the critical stuff to a second location, just in case.

Over 36 hours later, and my rig is not up and running like it used to. It still requires more application installations, and bug fixes. MSI Afterburner is telling me my side-by-side configuration is incorrect, and my powerline networking adapter isn't working anymore, so I'll have to get to the bottom of that too. Right now I'm using a WiPi adapter for a Raspberry Pi, and it's slow, but hasn't dropped the connection once, unlike the TRENDnet wifi dongle I bought.

Sure, my rig boots faster, and applications load faster, but I'm not totally convinced this was a good idea :(. I'm pretty close to saying I overestimated myself and I never should have undertaken such a complicated project, so let this be a warning: SSDs are not magic. They don't magically install themselves, they don't magically make applications boot instantly, and they can be a real pain to install and configure, no matter what you hear. Needless to say, this may not be applicable to every SSD, but it's what I learned from my experience.

I'm tired of fixing things that never went wrong before, so I might not be as enthusiastic or optimistic about my rig right now, but that is a danger of PC building, I guess.

I quote myself from earlier: "SSD!!! :D (Needless to say, I'm really excited): I want one to speed up my boot times and load times for Planetside 2, Minecraft and the likes. I'm looking at a 240GB (sic) Samsung 850 Evo, but I'm not sure I want to spend that much, or if I can truly justify the price in the first place."

"Needless to say" I thought SSDs were amazing. Not so much anymore. They're potentially powerful tools, but you have to be really dedicated and really know what you're doing before you mess with installing one...

Update 2

Afterburner is now working after (yet another) fresh installation, but the powerline networking adapter is still nonfunctional.

Update 3

The powerline networking adapter is now functional. It appears the LAN driver was never installed by MSI Live Update along with the rest of the drivers... I also updated Java, since JAR files asked me to find a program to open them with (they ran just fine before the SSD Update). JAR files and Java webpage contents now work.

UPDATE 02/23/15

CPU is now OC’d to 4.5 GHz (1 GHz above stock), and seems to be stable under benchmarks and gaming. We’ll see if it holds up. Added an extra 0.025 volts to what I tried before and that did it. Next I'll try lower voltages in order to (hopefully) lower temps.

I'll also do some testing with the GPU clocked to 1.1 GHz, and possibly move the graphics card lower and remove the second drive cage, if I can find a place to put the HDD.

UPDATE 03/08/15

I replaced the front (intake) fans with the now-listed Phanteks PH-F140SP fans, and switched the Fractal Design Silent Series R2 fans that came with the case to the back (exhaust) mounts. The Phanteks barely fit in the front mounts, due to the rubber padding, but I managed to get them in place.

I also installed the NZXT Sentry Mix 2 fan controller in the bottom 5 1/4 inch bay. This fit fine, with the exception of the right corner, which I have to push very hard on to get the screws to line up, and now sticks out slightly. I removed it to see what the problem was, but couldn't find the obstruction.

UPDATE 11/16/15

I picked up a NVidia Quadro NVS 290 (from 2007 or 2008, I think) and installed it along side my R9 280X. This works fine, and GeForce drivers should too, in theory. I only did it to test the multi-driver setup, because I could get the card cheap. I may later get a GTX 750 Ti or 950 and install it alongside my R9 280X to use for CUDA acceleration. After a while I may just replace the both of them with (hopefully, depending on the price) a 980 or 980 Ti, and move them over to another rig. That said, upgrading the CPU and RAM comes first.

UPDATE 12/07/15

I replaced my video card with an EVGA Superclocked GTX 970. Not because my R9 280X died, but because it's the first part I'm acquiring for my new workstation, and I might as well run it in the current rig. This thing is even more powerful than the 280X, and I haven't noticed a drop in GPU accelerated applications compared to my previous card, despite the lower core count.

Part Reviews


Fast at stock, (my sample) overclocks OK... Runs fairly cool.

CPU Cooler

Pretty cheap, cools well, looks OK.


Stable, nice overclocking, easy-to-use BIOS.


Stable and looks OK. The speed isn't holding anything back.


Fast., decent amount of storage


It's quiet, stores data and hasn't failed yet. That's all you can ask for in a HDD.


Fairly quite (until you fill it with fans), well built, looks nice, the door is annoying though.

Power Supply

Tier 2 PSU, reliable and efficient. Not enough connectors for multi-GPU setups though...

Optical Drive

Very loud. It does what it's supposed to though...

Operating System

Hate on it if you want, but it's great with 3rd party applications like Classic Shell. I do miss the Aero theme though (and the '97 reskin option)...

Case Fan

Pros: Cheap

Cons: Falls apart upon use. The pins in the Molex connector are so loose plugging it in to a power connector will push the pins out the back of the connector... They do work though...

Case Fan

They move enough air, but they're louder than you'd think :/. Not too bad, but audible.


Great color, no noticeable bleeding, no dead or stuck pixels, good for photo editing and gaming too!


The mouse is nice, but the keyboard feels a little clunky (high travel and bottoming out), and there's a weird rubbery matte coating on the keys that's kind of unpleasant for your fingernails...


Fits just over your ears, clamps down with some force (but not too much).


Beautiful sound, uncomfortable after prolonged use. The "wings" on the top dig into your head after a while.

Log in to rate comments or to post a comment.


  • 65 months ago
  • 2 points

Still working on uploading more pictures and temps...

  • 65 months ago
  • 1 point

Do you play dayz? I might have to get that 4690k and I wanted it to be fast in windows and in performance with programs, thanks!

  • 65 months ago
  • 1 point

Good call going with intel. Wish I had. My fx 8350 blew up almost my entire pc after a month.

  • 65 months ago
  • 3 points

That sounds like your fault

  • 65 months ago
  • 1 point


  • 65 months ago
  • 1 point

don't worry. that stuff happens... is it fixable?

  • 65 months ago
  • 1 point

I know a guy with a FX 8350. he has it under a Corsair H110i, if that helps..

  • 65 months ago
  • 3 points

I have seen them with a CM Hyper 212 EVO with reasonable temps.

  • 65 months ago
  • 2 points

I just had the stock cooler on it... But I had bought everything at the same time, So I just RMA'd a bunch of parts. First the mobo because it was visibly destroyed, and then I found out the cpu was ruined so I sent that back. So I finally got everything up and running and found out one of my ram sticks are shot so I had to send both back since it was a pair. Nightmare. Haha. It was down for over a month. As soon as I got it up and running again I put an H100i on it

  • 65 months ago
  • 2 points

My brother has one using a stock cooler, and its getting 20c on idle and maybe 80 on full load if that.

  • 41 months ago
  • 1 point

HA! I was a noob.

I was soooooo wrong on not upgrading that thing. I played with cooling and storage endlessly, and with my second rig I've done even more. I just can't leave stuff be....

[comment deleted by staff]
  • 65 months ago
  • 1 point

Sweet! Thank you so much for the info! I'll look into the RS HDR 180 for my next upgrade...

I've been looking for a headphone upgrade; the reason I bought the 202s is because I needed something that would block out some sound for commuting, and because they were really cheap. Unfortunately, both of these make them less than ideal for a PC setup...

  • 65 months ago
  • 1 point

I checked on the RS HDR 180 headphones, and I'm not sure if the HDR 108s will work without the base station/transmitter/stand of the RS 180, since the HDRs are meant as additional or replacement phones... Is this true?

I love the idea of the RS 180s, but having to buy the stand too adds to the price :/


[comment deleted by staff]
[comment deleted by staff]
[comment deleted by staff]
  • 65 months ago
  • 1 point

Thanks! I'll definitely do some research and put these on my future upgrades list!

[comment deleted by staff]
[comment deleted by staff]